Crowding as an Agronomic Factor Determining the Development of Plants and the Productivity of Linseed (Linum usitatissimum L.)

ABSTRACT

Nine sowing densities of linseed were compared in a two-year experiment. Self-regulation of the density of a linseed stand resulted in a differentiated branching of the plants. The number of capsules on a linseed shoot, as well as seeds in the capsule, and the number of seeds from the shoot were highly varied from year to year, and there is even a stronger differentiation in the weight of 1000 seeds. Linear relationships were noted between the mass of seeds from the linseed plant and the number of capsules. The yield of linseed was affected by both factors. An increasing sowing rate reduced the seed yield from the shoot and the plant. At lower seeding rates, the lateral shoots contributed in the seeds yield of the plant to a higher degree compared to the main ones.     

Comparative analysis of formaldehyde and toluene sorption on indoor floorings and consequence on Indoor Air Quality

Indoor surfaces may be adsorptive sinks with the potential to change Indoor Air Quality. To estimate this effect, the sorption parameters of formaldehyde and toluene were assessed on five floorings by an experimental method using solid-phase microextraction in an airtight emission cell. Adsorption rate constants ranged from 0.003 to 0.075 m·h⁻¹, desorption rate constants from 0.019 to 0.51 h⁻¹, and the partition coefficient from 0.005 to 3.9 m, and these parameters vary greatly from one volatile organic compound/material couple to another indicating contrasted sorption behaviors. A rubber was identified as a sink of formaldehyde characterized by a very low desorption constant close to 0. For these sorbent floorings identified, the adsorption rates of formaldehyde are from 2 to 4 times higher than those of toluene. Two models were used to evaluate the sink effects of floorings on indoor pollutant concentrations in one room from different realistic conditions. The scenarios tested came to the conclusion that the formaldehyde sorption on one rubber (identified as a sink) has a maximum contribution from 15% to 21% for the conditions of low air exchange rate. For other floorings, the sorption has a minor contribution less than or equal to 5%, regardless of the air exchange rate.     

不同工质回路热管负载功率变化下的质量流量特性

为了进一步提高回路热管仿真精度并丰富回路热管实验研究方法，本文对回路热管瞬态传质进行实验研究。使用高精度质量流量计分别对以丙酮、乙醇、丙烯为工质的回路热管进行不同负载功率下的质量流量测量研究。结果表明：启动阶段，热负载10W时，丙烯回路比丙酮回路热管启动快，且两者的温度稳定均滞后于质量流量；稳定阶段，随着热负载功率增大，不同工质的回路热管的平均质量流量均线性增长，而瞬态质量流量则持续波动，其质量流量波动幅度均呈现先减小后增大的趋势。质量流量波动幅度会受到气体工质的可压缩性与作用在毛细芯内部上的热量的共同影响。通过频谱分析发现，液相质量流量波动还会受到冷凝器两相区的影响。高热负载下，作用在毛细芯内部上的热量占主导地位，质量流量波动加剧，同时出现周期性大幅波动，且其波动频率随着热负载增大而增大。     

复杂炼油塔模拟的改进联立方程内外层算法

在内外层算法的基础上，采用联立方程思想将主塔、侧线汽提塔视为一个整体进行建模，并针对复杂炼油塔的特点对算法提出了改进。首先，由于传统内外层法简化的K值模型对组成的变化不敏感，在处理带有石油的体系时，容易出现迭代次数较多，甚至部分塔板温度更新异常的问题，因此采用了汽相分数加和式推导了简化的K值模型加权因子。其次，借鉴流量加和法思想，规定侧线汽提塔的塔底产品流量作为设计变量，增强了算法收敛的稳定性。为验证改进后算法的有效性，采用不同的算法对实际的常压塔进行了模拟，结果显示改进后的算法适合应用于复杂炼油塔的模拟计算。     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

压水堆核电厂一回路首次钝化工艺研究

压水堆核电厂热态功能试验中的一回路首次钝化对核电厂一回路材料腐蚀控制和减少腐蚀产物等方面具有重要作用。本文结合理论研究与工程实际情况，提出了在热态功能试验过程中钝化膜的生成包含电化学反应和化学反应的观点，阐述了双层膜的生长机理，解释了用电化学测试方法分析钝化工艺过程的合理性，推导出钝化温度与钝化膜反应速率的函数关系式，钝化温度升高，反应速率升高，钝化时间缩短；明确了钝化工艺温度的理论限值应不低于260℃。      

压水堆核电厂堆外源量程探测器计数率分析

压水堆核电厂启动过程中，次级中子源为堆外源量程探测器提供本底计数率，避免测量盲区，确保反应堆安全启动。但次级中子源的引入会为核电厂带来较大的经济和环境负担，同时也需承受次级中子源破损等带来的风险。为此，可使用受辐照燃料组件的自发裂变中子源进行替代，即无源启动方式。通过研究堆外源量程探测器计数率的理论计算方法，并基于运行电厂测量数据进行分析验证，为源量程探测器计数率的理论预估提供了较为完善的理论方法流程。本文结果可为无源启动源量程探测器计数率分析提供支持，同时也可用于次级中子源装载量或布置位置的优化分析等。     

Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

生物质纤维和改性木质素对聚乳酸结晶性能的影响

采用改性木质素(MZS)作为成核剂,生物质纤维(BF)作为增强剂,通过双螺杆挤出机制备了生物降解的聚乳酸(PLA)/BF/MZS材料。采用差式扫量热仪(DSC)、电子万能试验机和扫描电子显微镜(SEM)分析了BF和MZS对PLA材料性能的影响。结果表明,BF和MZS有效提高了PLA的结晶能力和力学性能。当BF和MZS的含量分别为15%和1%时,PLA材料结晶度提高至67.1%,在50℃/min降温速率下仍具有较高的结晶能力。105℃等温结晶时,15%BF和1%MZS的PLA材料半结晶时间降低至9.0 s,比纯PLA缩短了72.2%。当PLA含有3%BF和1%MZS时,拉伸强度和冲击强度分别为70.1 MPa和7.4 kJ/m^2,比纯PLA分别提高了7.8%和10.4%,根据SEM显示,当BF含量为3%时,在PLA材料中分布较均匀。     

一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.